Videos tagged with Case Resizing

This video demonstrates the process of reloading ammunition using the RCBS Rock Chucker Supreme single-stage press. It highlights the simplicity and precision of the Rock Chucker Supreme, making it an excellent choice for beginners and experienced reloaders alike. The guide covers essential steps from resizing and decapping to priming, powder charging, bullet seating, and crimping, emphasizing the methodical and relaxing nature of the reloading process.

This video explains how a bullet setback, caused by improper case resizing and excessive powder compression, can lead to dangerous pressure spikes in handguns. Reloaders are advised to carefully select components, properly resize cases to maintain neck tension, and use propellants suited to the caliber to avoid a 'perfect storm' of conditions that could cause firearm damage or injury.

This guide details the process of reloading ammunition using the Lee Classic Loader, presented as the most affordable entry into handloading. It covers step-by-step instructions for depriming, resizing, priming, flaring the case mouth, charging with powder, seating the bullet, and crimping the case, emphasizing the use of a rubber mallet and the included tools. The video highlights the simplicity and low cost of this reloading method.

This video details the process and challenges of reloading .410 shotshells for a Smith & Wesson Governor. The reviewer highlights issues with hand crimping, leading to unburnt powder and potential chambering difficulties. Despite these challenges, the reloaded triple-aught buckshot and bird shot demonstrated acceptable performance at close range, with the buckshot patterning effectively within 7 yards.

This guide details the initial brass preparation for reloading the 6.5 PRC cartridge. It covers inspecting and lubricating brass, performing neck and full-length resizing, troubleshooting stuck cases, and preparing cases for priming. The process highlights the importance of proper die setup and lubricant selection for successful reloading.

This guide details the step-by-step operation of the Hornady Lock-n-Load AP Progressive Press, a 5-station system for efficient ammunition reloading. It covers primer system preparation, the loading cycle for pistol and rifle cartridges, powder verification using the Powder Cop die, bullet seating, and essential safety checks. The instruction emphasizes consulting reloading manuals and using measurement tools for accuracy and safety.

This video details the process of reloading 6.5 Creedmoor brass, focusing on proper resizing techniques to maximize brass life. The instructor demonstrates how to use a headspace comparator to ensure the shoulder is bumped back only 1-2 thousandths of an inch, preserving the brass for multiple firings. The guide covers case lubrication, resizing die setup, and post-sizing cleaning and preparation.

This video details the process of preparing previously fired 22 Nosler brass for reloading, addressing extraction issues encountered in previous videos. The presenter focuses on resizing, trimming (or deciding not to trim based on measurements), and seating bullets for optimal magazine fit. The guide highlights the importance of careful brass preparation and monitoring case dimensions to ensure reliable function, especially when dealing with potential extraction problems.

This guide details the essential process of lubricating cases for resizing, drawing on over 40 years of reloading experience. It covers proper case neck preparation, the application of various lubricants (commercial and improvised), techniques to avoid common mistakes like hydraulic denting, and effective post-reloading cleanup methods. The instruction emphasizes practical, cost-effective solutions for reloaders.

This YouTube video, "Loading 300 Blk - ep 18 - Revisiting the Subject of Dies," is the eighteenth installment in a series focused on reloading ammunition for the 300 Blackout (300 Blk) caliber. The episode specifically revisits the topic of reloading dies, which are critical tools for resizing spent cartridge cases and seating new bullets. This suggests a detailed discussion and demonstration of different types of dies, their functions, and potentially best practices for using them in the reloading process for this popular rifle cartridge.

This YouTube video provides a quick tip on the Redding S Die Bushing, explaining its purpose and demonstrating its installation. Steve Ostrem guides viewers through the process, highlighting the specific Redding 73 Style Steel Bushing (part number 749-001-993). The video aims to educate reloaders on this particular component for case resizing.

This guide details the process of reloading 7.62x54R ammunition for a Mosin Nagant rifle, focusing on using Reloader 15 powder. It covers essential steps like bore slugging to determine barrel diameter, proper case resizing techniques for bolt-action firearms, consistent powder charging, and bullet seating. The video emphasizes testing for accuracy and understanding the impact of barrel heat on point of impact.